Designers and manufacturers of Residual Current Devices (RCD) for Ground Fault Protection and Earth Leakage Detection.

• 24 – 240 V AC or DC Control Voltage.

• For 45 - 450 Hz power systems.

• Internal current sensor: 28 mm with 500:1 ratio.

• Ext CS with wire break/short supervision.

• Trip points in primary currents for:

• Delay times:
  with Trip Inhibit 20, 100, 300 ms.
  without Trip Inhibit 20, 100, 300, 1000, 3000 ms.

• Operating modes: Continuous Non-Failsafe, Continuous Failsafe, Pulsed Non-Failsafe, Pulsed Failsafe.

• Tamperproof dipswitches.

• Trip Inhibit function.

• c-UL-us certified.

• 2 signal LEDs.

• Memory after loss of Control Voltage.

• Built-in Reset/Test pushbutton.

• Optional: external sensor, remote reset button and DGF7 Display.

Go to manual

Go to product page

Digital Display Unit with LCD display for use with DGF7-3 or DGF7-61 units

• Door mounted operator interface.

• Four digit LCD panel.

• Shows actual G/F current in relative or absolute mode.

• Auto ranging.

• Refreshes every 0,5 seconds.

• Shows current G/F Trip Level setting.

• Indicates cause of trip using codes.

• Memory after loss of Control Voltage.

• Ability to test and reset the conected unit.

• Ability to test the LCD panel.

• Actual current reading can be adjusted according to the connected CS ratio.

• Connected by a single twisted pair of wires.

Go to manual

Go to product page

• 24 – 240 V AC or DC Control Voltage.

• For 45 - 450 Hz power systems.

• Internal current sensor: 28 mm with 500:1 ratio.

• Trip points in primary currents for: 500:1Primary current trip points with 500:1 ratio int./ext. sensors:
  1 - 1,5 - 2 - 2,5 - 4 - 6 - 8 - 10 A. 1000:1Primary current trip points with 1000:1 ratio external sensors:
  2 - 3 - 4 - 5 - 8 - 12 - 16 - 20 A. 2000:1Primary current trip points with 2000:1 ratio external sensors:
  4 - 6 - 8 - 10 - 16 - 24 - 32 - 40 A. 10.000:1Primary current trip points with 10.000:1 ratio external sensors:
  20 - 30 - 40 - 50 - 80 - 120 - 160 - 200 A.

• Delay times: 500, 1000, 1500, 2000, 2500, 5000, 7500, 10.000 ms.

• Operating modes: Continuous Non-Failsafe, Continuous Failsafe, Pulsed auto reset, Pulsed Non-Failsafe.

• c-UL-us certified.

• 1 signal LED.

• Optional: external sensor, remote reset/test button, remote voltmeter.

Go to manual

Go to product page

• 24 – 240 V AC or DC Control Voltage.

• For 45 - 450 Hz power systems.

• Internal current sensor: 28 mm with 500:1 ratio.

• Trip points in primary currents for:

• Delay times: 500, 1000, 1500, 2000, 2500, 5000, 7500, 10.000 ms.

• Operating modes: Continuous Non-Failsafe, Continuous Failsafe, Pulsed auto reset, Pulsed Non-Failsafe.

• c-UL-us certified.

• 1 signal LED.

• Optional: external sensor, remote reset/test button, remote voltmeter.

Go to manual

Go to product page

• 24 – 240 V AC or DC Control Voltage.

• For 45 - 450 Hz power systems.

• Internal current sensor: 28 mm with 500:1 ratio.

• Trip points in primary currents for: 500:1Primary current trip points with 500:1 ratio int./ext. sensors :
  30 - 120 - 210 - 300 - 600 mA.
  2,4 - 4,2 - 6 A. 1000:1Primary current trip points with 1000:1 ratio external sensors:
  60 - 240 - 420 - 600 mA.
  1,2 - 4,8 - 8,4 - 12 A. 2000:1Primary current trip points with 2000:1 ratio external sensors:
  120 - 480 - 840 mA.
  1,2 - 2,4 - 9,6 - 16,8 - 24 A. 10.000:1Primary current trip points with 10.000:1 ratio external sensors:
  600 mA.
  2,4 - 4,2 - 6,0 - 12 - 48 - 84 - 120 A.

• Delay times:
  20 (instantaneous) and 500 ms.

• Operating modes: Continuous Non-Failsafe , Pulsed Trip/Auto Reset.

• c-UL-us certified.

• 1 signal LED.

• Optional: External sensor and remote reset/test button.

Go to manual

Go to product page

• 24 – 240 V AC or DC Control Voltage.

• For 45 - 450 Hz power systems.

• Internal current sensor: 28 mm with 500:1 ratio.

• Trip points in primary currents for:

• Delay times:
  20 (instantaneous) and 500 ms.

• Operating modes: Continuous Non-Failsafe , Pulsed Trip/Auto Reset.

• c-UL-us certified.

• 1 signal LED.

• Optional: External sensor and remote reset/test button.

Go to manual

Go to product page

• 24 – 240 V AC or DC Control Voltage.

• For 45 - 450 Hz power systems.

• No internal current sensor.

• Ext CS with wire break/short supervision active on Series C, inactive on Series D.

• Trip points in primary currents for: 500:1Primary current trip points with 500:1 ratio external sensors:
  30 - 100 - 500 mA.
  1 - 2 -3 - 5 - 9 A. 1000:1Primary current trip points with 1000:1 ratio external sensors:
  60 - 200 mA.
  1 - 2 - 4 - 6 - 10 - 18 A. 2000:1Primary current trip points with 2000:1 ratio external sensors:
  120 - 400 mA.
  2 - 4 - 8 - 12 - 20 - 36 A. 10.000:1Primary current trip points with 10.000:1 ratio external sensors:
  600 mA.
  2 - 10 - 20 - 40 - 60 - 100 - 180 A.

• Delay times:
  with Trip Inhibit 20, 300 ms.
  without Trip Inhibit 20, 300, 1000, 2000, 3000, 10.000 ms.

• Operating modes: Continuous Non-Failsafe, Continuous Failsafe, Pulsed Non-Failsafe, Pulsed Failsafe.

• Tamperproof dipswitches.

• Trip Inhibit function.

• c-UL-us certified.

• 2 signal LEDs.

• Memory after loss of Control Voltage.

• Built-in Reset/Test pushbutton.

Go to manual

Go to product page

• 24 – 240 V AC or DC Control Voltage.

• For 45 - 450 Hz power systems.

• No internal current sensor.

• Ext CS with wire break/short supervision active on Series C, inactive on Series D.

• Trip points in primary currents for:

• Delay times:
  with Trip Inhibit 20, 300 ms.
  without Trip Inhibit 20, 300, 1000, 2000, 3000, 10.000 ms.

• Operating modes: Continuous Non-Failsafe, Continuous Failsafe, Pulsed Non-Failsafe, Pulsed Failsafe.

• Tamperproof dipswitches.

• Trip Inhibit function.

• c-UL-us certified.

• 2 signal LEDs.

• Memory after loss of Control Voltage.

• Built-in Reset/Test pushbutton.

Go to manual

Go to product page

• 24 – 240 V AC or DC Control Voltage.

• For 45 - 450 Hz power systems.

• Internal current sensor: 46 mm with 500:1 ratio.

• Trip points in primary currents for: 500:1Primary current trip points with 500:1 ratio int./ext. sensors:
  30 - 40 - 60 - 90 - 150 - 250 - 400 - 600 - 900 mA.
  1,5 - 2,5 - 4 - 6 - 9 A. 1000:1Primary current trip points with 1000:1 ratio external sensors:
  60 - 80 - 120 - 180 - 300 - 500 - 800 mA.
  1,2 - 1,8 - 3 - 5 - 8 - 12 - 18 A. 2000:1Primary current trip points with 2000:1 ratio external sensors:
  120 - 160 - 240 - 360 - 600mA.
  1 - 1,6 - 2,4 - 3,6 - 6 - 10 - 16 - 24 - 36 A. 10.000:1Primary current trip points with 10.000:1 ratio external sensors:
  600 - 800 mA.
  1,2 - 1,8 - 3 - 5 - 8 - 12 - 18 - 30 - 50 - 80 - 120 - 180 A.

• Delay times: 20, 50, 100, 200, 500, 1000, 2000 and 5000 ms.

• Operating modes: Continuous Non-Failsafe, Continuous Failsafe, Pulsed Auto Reset, Pulsed Non-Failsafe.

• c-UL-us certified.

• 2 signal LEDs.

• Built-in Reset/Test pushbutton.

• Optional: external sensor, remote reset/test button and DGF100 Display.

Go to manual

Go to product page

• 24 – 240 V AC or DC Control Voltage.

• For 45 - 450 Hz power systems.

• Internal current sensor: 46 mm with 500:1 ratio.

• Trip points in primary currents for:

• Delay times: 20, 50, 100, 200, 500, 1000, 2000 and 5000 ms.

• Operating modes: Continuous Non-Failsafe, Continuous Failsafe, Pulsed Auto Reset, Pulsed Non-Failsafe.

• c-UL-us certified.

• 2 signal LEDs.

• Built-in Reset/Test pushbutton.

• Optional: external sensor, remote reset/test button and DGF100 Display.

Go to manual

Go to product page

Digital Display Unit with LCD display and interconnecting cable, for use with DGF100.

• Door mounted operator interface.

• Four digit LCD panel.

• 2 signal LEDs.

• Shows actual G/F current.

• Auto ranging.

• Trip memory after loss of Control Voltage.

• Ability to reset the DGF100.

• Ability to test the DGF100, this mode can be enabled/disabled.

• Ability to test the LCD panel.

• Connected by a RJ-10 type connector with 4-wire telephone cable.

Go to manual

Go to product page

Digital Display Unit with LCD display and interconnecting cable, for use with DGF100.

• Door mounted operator interface.

• Four digit LCD panel.

• 2 signal LEDs.

• Shows actual G/F current.

• Auto ranging.

• Memory after loss of Control Voltage.

• Ability to reset the DGF100.

• Ability to test the DGF100, this mode can be enabled/disabled.

• Ability to test the LCD panel.

• Connected by a RJ-10 type connector with 4-wire telephone cable.

Go to manual

Go to product page